Samson S2000 Instrucciones de operaciones Pagina 64
- Pagina / 124
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
(Code 8) and travel/angle range end
(Code 9).
Enable configuration:
Note: If no settings are entered within
120 seconds, the enabled configuration
function becomes invalid.
Default No
Turn
→
Code 3, display: No
Press , Code 3 blinks
Turn
→
YES
Press , display
Enter the pin position:
Pin position
Default
No
Turn
→
Code 4
Press , Code 4 blinks
Turn
→
Pin position on lever (see rele
-
vant section on attachment)
Press . The reading of the nominal range
appears in mm/°.
Select the initialization mode:
Initialization mode
Default
MAX
Turn
→
Code 6
Press , Code 6 blinks
Turn
→
MAN
Press to confirm the MAN as the initial
-
ization mode.
Enter OPEN position:
Manual set point
(the current angle of rota-
tion is displayed)
Turn
→
Code 0
Press , Code 0 blinks
Turn
→
MAN
Press
Turn
→
Code
1
Press , Code 1 blinks
Turn until the valve reaches its OPEN po
-
sition.
Press to confirm the OPEN position.
Start initialization:
4
Press INIT key to start initialization!
64 EB 8384-4 EN
Start-up – Settings
mm
- Mounting and 1
- Operating Instructions 1
- EB 8384-4 EN (1300-1613) 1
- EB 8384-4 EN 3 3
- EB 8384-4 EN 5 5
- Vent opening 6
- 2 Article code 7
- 3 Design and principle of 8
- 3.1 Additional equipment 9
- 3.2 Communication 10
- 3.2.1 Configuration using 10
- TROVIS-VIEW software 10
- 3.3 Technical data 11
- 12 EB 8384-4 EN 12
- 4 Attachment to the control 14
- 4.1 Direct attachment 16
- 4.1.1 Type 3277-5 Actuator 16
- 4.1.2 Type 3277 Actuator 18
- 4.2 Attachment according to 20
- IEC 60534-6 (NAMUR) 20
- 4.3 Attachment according to 22
- VDI/VDE 3847 22
- Actuator stem 24
- EB 8384-4 EN 25 25
- 4.4 Attachment to Type 3510 28
- Micro-flow Valve 28
- 4.5 Attachment to rotary 30
- 4.5.1 Heavy-duty version 32
- 4.6 Reversing amplifier for 34
- 4.6.1 Reversing amplifier 34
- (1079-1118 or 1079-1119) 34
- From the positioner 35
- Control signals to 35
- 4.7 Attaching an external 36
- 4.7.1 Mounting the position 36
- 1.1, 1.2 14.1 3 14 99.1 38
- 4.7.3 Mounting the position 39
- 2 1 1.1, 1.2 40
- 4.9 Air purging function for 41
- 4.10 Mounting parts and 42
- 44 EB 8384-4 EN 44
- Table 6 · General accessories 45
- 46 EB 8384-4 EN 46
- 5 Connections 47
- 5.1 Pneumatic connections 47
- 5.1.1 Signal pressure gauges 47
- 5.1.2 Supply pressure 47
- 5.2 Electrical connections 48
- EB 8384-4 EN 49 49
- 24 V DC BE1 BE2 50
- EB 8384-4 EN 51 51
- 52 EB 8384-4 EN 52
- Connections 52
- 6 Operator controls and 53
- 7 Start-up – Settings 56
- 7.1 Defining the valve closed 56
- 7.3 Adapting the display 57
- 7.5 Checking the operating 58
- Manual reference variable 59
- EB 8384-4 EN 59 59
- 7.6 Initialization 60
- Default No 65
- Nominal range 65
- (locked with Code 4 = No) 65
- EB 8384-4 EN 65 65
- 7.7 Zero calibration 68
- 7.8 Reset to default values 68
- 7.10 Setting the bus address 69
- 8 Operation 70
- 8.1 Enabling and selecting 70
- 8.2 Operating modes 71
- 8.2.1 Automatic and manual 71
- 8.3 Malfunction/maintenance 73
- Error caused by pin 74
- 9 Adjusting the limit switch 75
- 10 Maintenance 78
- 12 Firmware update (serial 78
- EB 8384-4 EN 79 79
- 14 Code list 80
- Code list 81
- 82 EB 8384-4 EN 82
- 84 EB 8384-4 EN 84
- 86 EB 8384-4 EN 86
- EB 8384-4 EN 87 87
- Initialization errors 88
- 88 EB 8384-4 EN 88
- Operational errors 90
- 90 EB 8384-4 EN 90
- Hardware errors 91
- Error appendix 92
- 92 EB 8384-4 EN 92
- Data errors 93
- 94 EB 8384-4 EN 94
- Diagnosis errors 95
- 15 Dimensions in mm 96
- EB 8384-4 EN 97 97
- Heavy-duty version 98
- Light version 98
- EB 8384-4 EN 100
- 102 EB 8384-4 EN 102
- EB 8384-4 EN 103 103
- 104 EB 8384-4 EN 104
- EB 8384-4 EN 105 105
- 106 EB 8384-4 EN 106
- EB 8384-4 EN 107 107
- 108 EB 8384-4 EN 108
- EB 8384-4 EN 109 109
- 110 EB 8384-4 EN 110
- EB 8384-4 EN 111 111
- 112 EB 8384-4 EN 112
- EB 8384-4 EN 113 113
- 114 EB 8384-4 EN 114
- EB 8384-4 EN 115 115
- EB 8384-4 EN 117 117
- Model 3730-43 118
- or 3730-53 118
- EB 8384-4 EN 119 119
- 122 EB 8384-4 EN 122
- EB 8384-4 EN 123 123
Relacionado con productos y manuales para Amplificadores de audio Samson S2000
Amplificadores de audio Samson 1200 Especificaciones
(60 paginas)
(60 paginas)
Amplificadores de audio Samson B Series B900 Manual
(60 paginas)
(60 paginas)
Amplificadores de audio Samson Studio Reference Monitor System Resolv 40a Manual de usuario
(11 paginas)
(11 paginas)
Amplificadores de audio Samson SCOM Especificaciones
(67 paginas)
(67 paginas)
(5 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.621 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales